Use the measuring tape to take exact lengths of the range hood vent. Afterward, head to the ceiling and indicate the spots with a marker. Size up the range hood vent and see if it fits the marked spots, just for confirmation. After marking the spots, the next step is to puncture holes on them.
To vent a range hood through a wall or roof, you have to open up a hole in the ceiling using a drill machine. The holes are not just for the range hood but also drill one or two more holes for the electric wires too. This particular step will require a level of pinpoint accuracy from you because once there is a mistake, the whole procedure goes south.
So ensure the openings are perfectly matched with the marked out spots. The task might be a little bit tough for a first-timer, just try to give it your best and drill an opening that lets the range hood outside the ceiling. Remember that you detached some units of the range hood vent to enable you to take measurement accurately?
Good, you should fix them in, so you install the device correctly. Be careful with the wire clips when fixing them together or you could call someone to help you hold them in place. All the initial steps have been leading up to this one, the installation of the range hood vent. All the efforts you have made are to ensure that this step goes without any hitch. Electrician Services ». Electrician Near Me ».
Toggle navigation. Which one you use will depend greatly on what you prefer and how much cooking you do. Ducted hoods are said to be more effective at removing odors and steam, since the air is circulated to the outside.
Ductless hoods, on the other hand, use a filter to recirculate air back into the kitchen. Before you start the process of installing your new range hood, note that this is an overview of the installation procedure. Additionally, if you do not feel comfortable performing this task yourself, hiring a professional is recommended. Prior to purchasing your new range hood, here are some considerations to make sure you pick the right one:.
Unplug the hood and disconnect all electrical wires. You may need the help of another person to help support the weight of the hood as you remove the support screws. Measure your new range hood to see where the vent will come out. If your vent came with a paper template, use it to measure the space on the wall where the vent hole will go.
First cut a small section of the wall where the vent will go before making the larger hole that the vent will go through. You can make the hole a little bigger to give you more room to work. Use a long drill bit to place locator holes extending to the outer wall. Place a locator hole on the edges of the vent hole. Before cutting the vent pipe hole that will be on the exterior wall, find the locator holes and connect them to form the circle that you will be cutting through.
If your exterior wall is paneled or uneven, then it might be easier to cut a square piece of PVC trim to place on the exterior wall and cut the hole through the trim. Attach with screws and caulk so that you get a tight seal that is also waterproof.
Use a small amount of duct to test that you have the correct measurements before cutting a bigger piece of duct. Mark the outside of the damper to reference where to tape the ductwork. If necessary, drill holes next to each side of the vent so that you can run the electrical wiring from the hood to the electrical box.
Ensure that your electrical wiring is up to code. If you do not feel confident running the electrical wiring, consulting with an electrician is strongly advised. You will need the help of a second person to support the weight of the hood while you place the mounting screws through the mounting slots of the hood. Remove the grease filter so that you have better access as you tighten screws to secure them. Level the hood and tighten the upper screws first.
Clip any excess wiring and strip back the wires to connect them with wire caps or connectors. Use mounting screws next and connect straps of outlet to the box. Turn on the power and test if it works. Troubleshoot for any mistaken step and finally connect the cover plate. This is where you need to make the mounting bracket holes. Trace down these holes into the paper. You want to redo measurements if necessary. Markdown the spots where these drywall screws will go through.
Insert the screws and tighten them. Stop when screws are barely protruding. These screws will hold the hanging range hood. Now you need to add those chimney brackets next. Place them directly on the ceiling and center line using drywall screws. Over the mounting screws, slip range hood and tighten them securely. You need to determine two studs that run behind range hood. Use stud finder for that. From beneath of hood, anchor it to the studs at marked lines.
Plug the range hood into an electric outlet and check if everything is working fine. Now you can finish by placing chimney.
0コメント