Step 1 : Input services. Step 2 : Locate Windows Search service and double-click it to open its Properties. Step 3 : Under General tab, choose Disabled from the drop-down menu of Startup type. Step 4 : Click Apply and OK to confirm the new settings.
If certain system files are corrupted, you might also fail to transfer large files and receive the error code 0xB. In this case, you can simply run the System File Checker which replaces the corrupted system files with the cached copies. Step 1 : Type cmd in the search box of Cortana and press Enter. Step 2 : Right-click Command Prompt from the search result and choose Run as administrator.
This tool will start scanning your computer and it will take about 15 minutes. When it comes to transferring large files, the file system of the destination drive should always be included in your consideration. If the target drive is FAT32 formatted, you cannot transfer files larger than 4GB to it and might receive the error 0xB. To do that, just click This PC icon, right-click the destination drive and select Properties. The file system is shown under the General tab.
Actually, you can format a hard drive to a certain file system in File Explorer or Disk Management tool. However, they are not recommended methods, as the data on the target drive will be removed by formatting. To avoid data loss, you can choose to convert the file system of the drive without formatting, which can be achieved in Command Prompt or a third-party program. You can also choose to utilize a reliable third-party tool, such as MiniTool Partition Wizard. Free Download. Step 3 : In the pop-up window, click Start button to start the operation instantly.
After converting to NTFS file system, you can try transferring the large files again and check if the error code 0xB disappears. Here are 2 methods.
Click to tweet. If an unexpected network error occurred when you are transferring files to another computer, perhaps there are file system errors on the target drive.
And some users have removed the issue by checking and fixing the file system errors. I frequently transfer large photo files the desktop, when renumbering photo files using PhotoShop, burning files to a DVD or BluRay, or when saving these files from a portable hard drive to the network hard drive.
The system has worked flawlessly up until recently. After returning from a trip in June, it began showing this error message when transferring large files, GB and up. The transfer speed varies up and down during the transfer, sometimes stopping all together, then starting again, but eventually it stops, and an error comes up, "An unexpected error is keeping you from copying the file.
If you continue to receive this error, you can use the error code to search for help with this problem. Error 0xB" It then shows the photo where the transfer stopped with its specifics, photo number, type, date taken etc. Under that it shows three buttons, "try Again" "Skip" and "Cancel". If I hit "try Again" the process will often resume, however, I need to be there to do that, and in most cases the file where it stopped dopes not transfer fully, the photo is damaged it was not damaged in the original folder.
In the past I've done very large file transfers that have literally taken 24 or more hours with no issue. I have changed all network cables to high quality CAT 6, changed the router, and the same problem occurs when on WiFi or hard wire. I've checked with the drive manufacturer, went through troubleshooting, shared the error code, and they say it's not a drive issue of course. Joined Apr 21, Messages 1, A simple test is to backup your config, install FreeNAS on a new thumbdrive, and restore your config, to see if the problem might be in some system file that was broke during an upgrade.
You might also have a bad drive. There's a post somewhere on the forums about testing drives. You should run through that and do a thorough check of everything. Hi bulsatar, sorry but what is your definition of package drop testing? Hi Nick, they are both good ideas, i'll give them a try. It will require setting up a static IP on both to test, but it'll help rule out any other network devices. Hi Everyone, Thanks for your help thus far, still haven't found the cause.
I started by doing Nick's suggestion and installed on a new thumb drive and uploaded my config file. I actually loaded the current release, as well as 9. It increased the ping to the NAS but didn't result in any packet loss. I've just setup S. Will let you know how it all goes.
Thanks again. T tests from the shell so am doing that now. G'day everyone, I took everyone's advice above - I ran short a few mins and long ish hours hard drive tests via shell and got zero errors detected. As a result I've come to the conclusion that our wifi router is screwed. It is clearly 'working' but something internally must be wrong with the actual hardware because a simple firmware upgrade or as i previously explained, downgrade has not solved the problems. I will go and buy a new router in the coming 24 hours and once that is setup, hopefully i can mark this thread as 'solved'.
Still find it absolutely bizarre that the problem as it was prevents copying to, but not from, the NAS.. It could be done weird QoS setting that for all screwed up. Have you tried resetting everything to defaults on the router? I don't recall resetting everything to defaults at all, but that said i don't usually fiddle with QoS unless something isn't working how i like and have never had any issues with this router until now.
Problem solved though.. Going to re-purpose the 'faulty' router as an access point after resetting it and see how it goes. If i have any issues i'll just bin the thing.
Thanks for your help everyone, appreciate your words of wisdom.
0コメント